Full Version : Kalash RK01 AKS-74U Disassembly
filakairsoft >>Take down, Upgrades & Modification! >>Kalash RK01 AKS-74U Disassembly


<< Prev | Next >>

alakdan.net [aka 9th]- 12-18-2008
Push Top Cover Lock, Tilt cover to open.
user posted image
user posted image
Take out Battery.

Now take out the Upper Handguard:
user posted image

Upper Handguard Lock:
user posted image

Take out the Lower Handguard by turning the lock:
user posted image
user posted image
user posted image

Take out the Charging handle, remove first the charging handle guide rod:
user posted image

Take out the front trunnion, remove large pin(1) and small pin(2), slide forward the trunnion:
user posted image

Just take extra careful with this part:
1.)The Top cover Hinges(yellow arrow) and 2.)Top cover "pusher"(blue arrow).
user posted image

Unscrew the Hex screw(1), then pull out the barrel(2):
user posted image

Remove the "L Block"(1) and the hop up securing screw, Tilt the inner barrel(2), Slide back the Hop & Inner Barrel above the mech box.
user posted image

Remove the Selector, get a cloth or tissue to cover the bolt (purpose: not to scratch), and use a pliers to remove the bolt.
user posted image

Remove Bushing:
user posted image

Take out the Hand grip, unscrew first(1) and remove the Hand grip(2)
user posted image

Carefully you can take out now the mech box from the top of the receiver.

Mech box and the inner barrel(with hop)
user posted image

Receiver and Front End:
user posted image


Acknowledgement:
Images Courtesy of: gocqb
Based from Post/Link: Yarik( URL-com or URL-net )

M76- 12-19-2008
filakairsoft/clap.gif filakairsoft/clap.gif filakairsoft/clap.gif thanks for the break down filakairsoft/clap.gif

alakdan.net [aka 9th]- 12-20-2008
You're welcome komrad.

Milgeek.co.uk- 05-24-2009
First of all, thank you Comrade alakdan for this excellent tutorial.

I will be disassembling my AK74U next month, upgrading some parts and adding a Madbull tight barrel, and this is where I would like to ask a question...

Your breakdown goes as far as removing the inner barrel with the hop-up attached, but how difficult is it to detach barrel from the hop-up and then reattach a new one?

I'd appreciate any advise,

Milgeek

M76- 05-24-2009
You should not have a problem removing the barrel out the Hop upunit and replacing it with a TB if you still struggel follow this below link it is the same as the RK02
hope this helps Gavin
Airsoft Barracks

Milgeek.co.uk- 05-24-2009
QUOTE (M76 @ May 25, 2009 02:43 am)
You should not have a problem removing the barrel out the Hop upunit and replacing it with a TB if you still struggel follow this below link it is the same as the RK02
hope this helps Gavin
Airsoft Barracks

Many thanks Gavin...

That looks fairly straight forward. I'll post up how I get on with this.

Cheers!

Milgeek

M76- 06-07-2009
here is a tip when putting the gearbox back in a kalash RK0 aeg, put the gear box back tighten the lever screw , but do not put the grip on yet , I found it very difficult to put back the spacer that keeps the hopup unit against the gearbox and seal . by doing this you are able to alin the and fit the hopup against the gearbox and then you can put the grip back. hope you understand what i am getting to

Bigbossy- 06-07-2009
Hooyah! up for this thread. very helpful. Thanks.

Forumer™ is Voted #1 Free Forum Hosting provider
Build your own community today with the largest message board hosting company.